Home > Product > SPCC-F Cold Rolled Steel Plate
Prodcuts List

Hot Rolled Steel Coil

Hot Rolled Steel Plate

Cold Rolled Steel Coil

Cold Rolled Steel Plate

Galvanized Steel Coil

Galvanized Steel Plate

Stainless Steel Coil

Stainless Steel Plate

Stainless Steel Pipe

Stainless Steel Bar

Pre-painted Steel Coil

Aluminum Plate

Carbon Steel Pipe


SPCC-F Cold Rolled Steel Plate

Cold rolled steel sheets & coils grade of SPCC is the Japanese steel grade, from JIS G3141.

Cold rolled steel sheets & coils grade of SPCC is the Japanese steel grade, from JIS G3141. Standard name: common & general use of cold-rolled carbon steel sheet and strip. The same category in the standard grades is SPCD, SPCE, SPCF, SPCG.

S: Steel
P: Plate
C: Cold
C: Common
D: Draw
E: Elongation
Technical data
Chemical Composition:
SPCC Grade: C≦0.15; Mn≦0.60; P≦0.100; S≦0.035
SPCCT Grade: C≦0.15; Mn≦0.60; P≦0.100; S≦0.035
SPCD Grade: : C≦0.10; Mn≦0.50; P≦0.040; S≦0.035
SPCE Grade: C≦0.08; Mn≦0.45; P≦0.030; S≦0.030
SPCF Grade: C≦0.06; Mn≦0.45; P≦0.030; S≦0.030
SPCG Grade: C≦0.02; Mn≦0.25; P≦0.020; S≦0.020

SPCC/SPCCT: Common & General Use; Characteristics: Suitable for bending processing and simple deep drawing processing, is the most demand varieties; Applications: Refrigerators, rails, switchboards, iron baskets and so on.

SPCD: Drawing & Stamping Use; Characteristics: Second only to SPCE, is the quality of the smaller deviation of the drawing steel plate; Applications: Automobile chassis, roof and so on.

SPCE/SPCF: Deep Drawing & Stamping Use; Characteristics: Grain is adjusted, deep drawing performance is excellent, after the stamping can get a beautiful surface. Applications: Car fender, rear side panels and so on.

SPCG: Extra-Deep Drawing & Stamping & Punching Use; Characteristics: Very low carbon cold rolled steel, excellent deep drawing processability. Applications: Car interior board, surface and so on.

Remarks: SPCCT is users specified the grade of SPCC which need to ensure that the tensile strength and extensibility of the species. SPCF, SPCG will need to ensure that there have non-aging (not due to the occurrence of tensile deformation of the property), after outside factory for 6 months – that is, SPCC, SPCD, SPCE if stored for a long time, will produce mechanical performance changes, especially to reduce the cold stamping performance, it should be used as soon as possible.

SPCC series catalog need to make provision for hardness and surface in advance when ordering.
Heat Treatment Code HRBS HV10
Annealed A – –
Annealed + Finishing S – –
1/8 hard 8 50~71 95~130
1/4 hard 4 65~80 115~150
1/2 hard 2 74~89 135~185
Full hard 1 ≥85 ≥170

FB: higher finishing surface: Does not affect the formability and coating, plating adhesion defects, such as small bubbles, small scratches, small roll, slightly scratched and oxidized color allowed to exist.

FC: advanced surface finishing: The better side of the steel plate must be further limited to the defect, no obvious visible defects, the other side should meet the FB surface requirements.

FD: extra-advanced surface finishing: The better side of the steel plate must be further limited to the defects, that is, does not affect the appearance of paint or after plating quality, the other side should meet the FB surface requirements.

Surface structure:
Surface Structure Code Average roughness Ra / μm
Pitting surface D 0.6~1.9
Bright surface B ≤0.9

Product Name

SPCC-F Cold Rolled Steel Plate

Width600-2050mm or as buyer’s requirement
Plate Weight           3-14 MT
Length            as buyer’s requirement
TechniqueCold rolled
ToleranceAs the standard or as required
ApplicationHousehold appliance, automobile, machine etc.
Packing details Standard seaworthy export packing or as required
DeliveryWithin 15 to 90 days, according to order quantity
PaymentT/T or L/C

Q: Where is the factory of delong
A:  Liaocheng city ,Shandong Province,China

Q:  Can I get some samples? 
A:  Yes, sample order is available for quality check and market test with freight fee collect. 

Q:  Do you receive customized order? 
A:  Yes, ODM & OEM are welcomed. you can give us drawings and we will manufacture accordingly.

Q:  What's the lead time? 
A:  According to the order quantity, small order usually need 7-15 days, big order need negotiation. 

Q:  What's your warranty terms? 
A:  We supply 12 months warranty time. 

Q:  What's your payment terms? 
A:  We accept T/T, LC etc.

Q:  Can you accept trail orders? 
A: Gemerally our MOQ is 1 ton.If your quanlity is smaller than our MOQ,kindly pls contact us for inquiry accordingly.

Dear customers, we will contact you as soon as possible after receiving your inquiry! Looking forward to cooperating with you!



We understand that this catalog may not answer all your questions. Please contact us , we will be happy to help you. Our goal is to return a quote to you within 24 hours.